| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
nexthop: fix IPv6 route referencing IPv4 nexthop
syzbot reported a panic [1] [2].
When an IPv6 nexthop is replaced with an IPv4 nexthop, the has_v4 flag
of all groups containing this nexthop is not updated. This is because
nh_group_v4_update is only called when replacing AF_INET to AF_INET6,
but the reverse direction (AF_INET6 to AF_INET) is missed.
This allows a stale has_v4=false to bypass fib6_check_nexthop, causing
IPv6 routes to be attached to groups that effectively contain only AF_INET
members. Subsequent route lookups then call nexthop_fib6_nh() which
returns NULL for the AF_INET member, leading to a NULL pointer
dereference.
Fix by calling nh_group_v4_update whenever the family changes, not just
AF_INET to AF_INET6.
Reproducer:
# AF_INET6 blackhole
ip -6 nexthop add id 1 blackhole
# group with has_v4=false
ip nexthop add id 100 group 1
# replace with AF_INET (no -6), has_v4 stays false
ip nexthop replace id 1 blackhole
# pass stale has_v4 check
ip -6 route add 2001:db8::/64 nhid 100
# panic
ping -6 2001:db8::1
[1] https://syzkaller.appspot.com/bug?id=e17283eb2f8dcf3dd9b47fe6f67a95f71faadad0
[2] https://syzkaller.appspot.com/bug?id=8699b6ae54c9f35837d925686208402949e12ef3 |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix potential NULL pointer deref in error path of ice_set_ringparam()
ice_set_ringparam nullifies tstamp_ring of temporary tx_rings, without
clearing ICE_TX_RING_FLAGS_TXTIME bit.
When ICE_TX_RING_FLAGS_TXTIME is set and the subsequent
ice_setup_tx_ring() call fails, a NULL pointer dereference could happen
in the unwinding sequence:
ice_clean_tx_ring()
-> ice_is_txtime_cfg() == true (ICE_TX_RING_FLAGS_TXTIME is set)
-> ice_free_tx_tstamp_ring()
-> ice_free_tstamp_ring()
-> tstamp_ring->desc (NULL deref)
Clear ICE_TX_RING_FLAGS_TXTIME bit to avoid the potential issue.
Note that this potential issue is found by manual code review.
Compile test only since unfortunately I don't have E830 devices. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: avoid NULL deref of conn->lnk in smc_msg_event tracepoint
The smc_msg_event tracepoint class, shared by smc_tx_sendmsg and
smc_rx_recvmsg, unconditionally dereferences smc->conn.lnk:
__string(name, smc->conn.lnk->ibname)
conn->lnk is only set for SMC-R; for SMC-D it is NULL. Other code on
these paths already handles this (e.g. !conn->lnk in
SMC_STAT_RMB_TX_SIZE_SMALL()). With the tracepoint enabled, the first
sendmsg()/recvmsg() on an SMC-D socket crashes:
Oops: general protection fault, probably for non-canonical address
KASAN: null-ptr-deref in range [...]
RIP: 0010:strlen+0x1e/0xa0
Call Trace:
trace_event_raw_event_smc_msg_event (net/smc/smc_tracepoint.h:44)
smc_rx_recvmsg (net/smc/smc_rx.c:515)
smc_recvmsg (net/smc/af_smc.c:2859)
__sys_recvfrom (net/socket.c:2315)
__x64_sys_recvfrom (net/socket.c:2326)
do_syscall_64
The faulting address 0x3e0 is offsetof(struct smc_link, ibname),
confirming the NULL ->lnk deref. Enabling the tracepoint requires
root, but the trigger itself is unprivileged: socket(AF_SMC, ...) has
no capability check, and SMC-D negotiation needs no admin step on
s390 or on x86 with the loopback ISM device loaded.
Log an empty device name for SMC-D instead of dereferencing NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
vrf: Fix a potential NPD when removing a port from a VRF
RCU readers that identified a net device as a VRF port using
netif_is_l3_slave() assume that a subsequent call to
netdev_master_upper_dev_get_rcu() will return a VRF device. They then
continue to dereference its l3mdev operations.
This assumption is not always correct and can result in a NPD [1]. There
is no RCU synchronization when removing a port from a VRF, so it is
possible for an RCU reader to see a new master device (e.g., a bridge)
that does not have l3mdev operations.
Fix by adding RCU synchronization after clearing the IFF_L3MDEV_SLAVE
flag. Skip this synchronization when a net device is removed from a VRF
as part of its deletion and when the VRF device itself is deleted. In
the latter case an RCU grace period will pass by the time RTNL is
released.
[1]
BUG: kernel NULL pointer dereference, address: 0000000000000000
[...]
RIP: 0010:l3mdev_fib_table_rcu (net/l3mdev/l3mdev.c:181)
[...]
Call Trace:
<TASK>
l3mdev_fib_table_by_index (net/l3mdev/l3mdev.c:201 net/l3mdev/l3mdev.c:189)
__inet_bind (net/ipv4/af_inet.c:499 (discriminator 3))
inet_bind_sk (net/ipv4/af_inet.c:469)
__sys_bind (./include/linux/file.h:62 (discriminator 1) ./include/linux/file.h:83 (discriminator 1) net/socket.c:1951 (discriminator 1))
__x64_sys_bind (net/socket.c:1969 (discriminator 1) net/socket.c:1967 (discriminator 1) net/socket.c:1967 (discriminator 1))
do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix dc_link NULL handling in HPD init
amdgpu_dm_hpd_init() may see connectors without a valid dc_link.
The code already checks dc_link for the polling decision, but later
unconditionally dereferences it when setting up HPD interrupts.
Assign dc_link early and skip connectors where it is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_irq.c:940 amdgpu_dm_hpd_init()
error: we previously assumed 'dc_link' could be null (see line 931)
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_irq.c
923 /*
924 * Analog connectors may be hot-plugged unlike other connector
925 * types that don't support HPD. Only poll analog connectors.
926 */
927 use_polling |=
928 amdgpu_dm_connector->dc_link &&
^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The patch adds this NULL check but hopefully it can be removed
929 dc_connector_supports_analog(amdgpu_dm_connector->dc_link->link_id.id);
930
931 dc_link = amdgpu_dm_connector->dc_link;
dc_link assigned here.
932
933 /*
934 * Get a base driver irq reference for hpd ints for the lifetime
935 * of dm. Note that only hpd interrupt types are registered with
936 * base driver; hpd_rx types aren't. IOW, amdgpu_irq_get/put on
937 * hpd_rx isn't available. DM currently controls hpd_rx
938 * explicitly with dc_interrupt_set()
939 */
--> 940 if (dc_link->irq_source_hpd != DC_IRQ_SOURCE_INVALID) {
^^^^^^^^^^^^^^^^^^^^^^^ If it's NULL then we are trouble because we dereference it here.
941 irq_type = dc_link->irq_source_hpd - DC_IRQ_SOURCE_HPD1;
942 /*
943 * TODO: There's a mismatch between mode_info.num_hpd
944 * and what bios reports as the # of connectors with hpd |
| In the Linux kernel, the following vulnerability has been resolved:
media: saa7164: add ioremap return checks and cleanups
Add checks for ioremap return values in saa7164_dev_setup(). If
ioremap for BAR0 or BAR2 fails, release the already allocated PCI
memory regions, remove the device from the global list, decrement
the device count, and return -ENODEV.
This prevents potential null pointer dereferences and ensures proper
cleanup on memory mapping failures. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/hdcp: Add NULL check for media_gt in intel_hdcp_gsc_check_status()
When media GT is disabled via configfs, there is no allocation for
media_gt, which is kept as NULL. In such scenario,
intel_hdcp_gsc_check_status() results in a kernel pagefault error due to
>->uc.gsc being evaluated as an invalid memory address.
Fix that by introducing a NULL check on media_gt and bailing out early
if so.
While at it, also drop the NULL check for gsc, since it can't be NULL if
media_gt is not NULL.
v2:
- Get address for gsc only after checking that gt is not NULL.
(Shuicheng)
- Drop the NULL check for gsc. (Shuicheng)
v3:
- Add "Fixes" and "Cc: <stable...>" tags. (Matt)
(cherry picked from commit bfaf87e84ca3ca3f6e275f9ae56da47a8b55ffd1) |
| In the Linux kernel, the following vulnerability has been resolved:
octeon_ep_vf: add NULL check for napi_build_skb()
napi_build_skb() can return NULL on allocation failure. In
__octep_vf_oq_process_rx(), the result is used directly without a NULL
check in both the single-buffer and multi-fragment paths, leading to a
NULL pointer dereference.
Add NULL checks after both napi_build_skb() calls, properly advancing
descriptors and consuming remaining fragments on failure. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/ocrdma: Don't NULL deref uctx on errors in ocrdma_copy_pd_uresp()
Sashiko points out that pd->uctx isn't initialized until late in the
function so all these error flow references are NULL and will crash. Use
the uctx that isn't NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: check for PCI upstream bridge existence
pci_upstream_bridge() returns NULL if the device is on a root bus. If
8821CE is installed in the system with such a PCI topology, the probing
routine will crash. This has probably been unnoticed as 8821CE is mostly
supplied in laptops where there is a PCI-to-PCI bridge located upstream
from the device. However the card might be installed on a system with
different configuration.
Check if the bridge does exist for the specific workaround to be applied.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: use a stable FDB dst snapshot in RCU readers
Local FDB entries can be rewritten in place by `fdb_delete_local()`, which
updates `f->dst` to another port or to `NULL` while keeping the entry
alive. Several bridge RCU readers inspect `f->dst`, including
`br_fdb_fillbuf()` through the `brforward_read()` sysfs path.
These readers currently load `f->dst` multiple times and can therefore
observe inconsistent values across the check and later dereference.
In `br_fdb_fillbuf()`, this means a concurrent local-FDB update can change
`f->dst` after the NULL check and before the `port_no` dereference,
leading to a NULL-ptr-deref.
Fix this by taking a single `READ_ONCE()` snapshot of `f->dst` in each
affected RCU reader and using that snapshot for the rest of the access
sequence. Also publish the in-place `f->dst` updates in `fdb_delete_local()`
with `WRITE_ONCE()` so the readers and writer use matching access patterns. |
| In the Linux kernel, the following vulnerability has been resolved:
rbd: fix null-ptr-deref when device_add_disk() fails
do_rbd_add() publishes the device with device_add() before calling
device_add_disk(). If device_add_disk() fails after device_add()
succeeds, the error path calls rbd_free_disk() directly and then later
falls through to rbd_dev_device_release(), which calls rbd_free_disk()
again. This double teardown can leave blk-mq cleanup operating on
invalid state and trigger a null-ptr-deref in
__blk_mq_free_map_and_rqs(), reached from blk_mq_free_tag_set().
Fix this by following the normal remove ordering: call device_del()
before rbd_dev_device_release() when device_add_disk() fails after
device_add(). That keeps the teardown sequence consistent and avoids
re-entering disk cleanup through the wrong path.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available.
We reproduced the bug on v7.0 with a real Ceph backend and a QEMU x86_64
guest booted with KASAN and CONFIG_FAILSLAB enabled. The reproducer
confines failslab injections to the __add_disk() range and injects
fail-nth while mapping an RBD image through
/sys/bus/rbd/add_single_major.
On the unpatched kernel, fail-nth=4 reliably triggered the fault:
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 UID: 0 PID: 273 Comm: bash Not tainted 7.0.0-01247-gd60bc1401583 #6 PREEMPT(lazy)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
RIP: 0010:__blk_mq_free_map_and_rqs+0x8c/0x240
Code: 00 00 48 8b 6b 60 41 89 f4 49 c1 e4 03 4c 01 e5 45 85 ed 0f 85 0a 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 e9 48 c1 e9 03 <80> 3c 01 00 0f 85 31 01 00 00 4c 8b 6d 00 4d 85 ed 0f 84 e2 00 00
RSP: 0018:ff1100000ab0fac8 EFLAGS: 00000246
RAX: dffffc0000000000 RBX: ff1100000c4806a0 RCX: 0000000000000000
RDX: 0000000000000002 RSI: 0000000000000000 RDI: ff1100000c4806f4
RBP: 0000000000000000 R08: 0000000000000001 R09: ffe21c000189001b
R10: ff1100000c4800df R11: ff1100006cf37be0 R12: 0000000000000000
R13: 0000000000000000 R14: ff1100000c480700 R15: ff1100000c480004
FS: 00007f0fbe8fe740(0000) GS:ff110000e5851000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe53473b2e0 CR3: 0000000012eef000 CR4: 00000000007516f0
PKRU: 55555554
Call Trace:
<TASK>
blk_mq_free_tag_set+0x77/0x460
do_rbd_add+0x1446/0x2b80
? __pfx_do_rbd_add+0x10/0x10
? lock_acquire+0x18c/0x300
? find_held_lock+0x2b/0x80
? sysfs_file_kobj+0xb6/0x1b0
? __pfx_sysfs_kf_write+0x10/0x10
kernfs_fop_write_iter+0x2f4/0x4a0
vfs_write+0x98e/0x1000
? expand_files+0x51f/0x850
? __pfx_vfs_write+0x10/0x10
ksys_write+0xf2/0x1d0
? __pfx_ksys_write+0x10/0x10
do_syscall_64+0x115/0x690
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f0fbea15907
Code: 10 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
RSP: 002b:00007ffe22346ea8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000058 RCX: 00007f0fbea15907
RDX: 0000000000000058 RSI: 0000563ace6c0ef0 RDI: 0000000000000001
RBP: 0000563ace6c0ef0 R08: 0000563ace6c0ef0 R09: 6b6435726d694141
R10: 5250337279762f78 R11: 0000000000000246 R12: 0000000000000058
R13: 00007f0fbeb1c780 R14: ff1100000c480700 R15: ff1100000c480004
</TASK>
With this fix applied, rerunning the reproducer over fail-nth=1..256
yields no KASAN reports.
[ idryomov: rename err_out_device_del -> err_out_device ] |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: Fix NULL pointer dereference in acpi_ev_address_space_dispatch()
Cover a missed execution path with a new check. |
| In the Linux kernel, the following vulnerability has been resolved:
cpuidle: Skip governor when only one idle state is available
On certain platforms (PowerNV systems without a power-mgt DT node),
cpuidle may register only a single idle state. In cases where that
single state is a polling state (state 0), the ladder governor may
incorrectly treat state 1 as the first usable state and pass an
out-of-bounds index. This can lead to a NULL enter callback being
invoked, ultimately resulting in a system crash.
[ 13.342636] cpuidle-powernv : Only Snooze is available
[ 13.351854] Faulting instruction address: 0x00000000
[ 13.376489] NIP [0000000000000000] 0x0
[ 13.378351] LR [c000000001e01974] cpuidle_enter_state+0x2c4/0x668
Fix this by adding a bail-out in cpuidle_select() that returns state 0
directly when state_count <= 1, bypassing the governor and keeping the
tick running. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/rocket: search every core slot when looking up a scheduler
sched_to_core() walks rdev->cores[] up to rdev->num_cores, and
rocket_remove() decrements num_cores for every core it removes. Unbind a
core that is not the last one and the cores behind it fall outside the
search, so sched_to_core() returns NULL for a core that is still bound and
still running jobs. Neither caller checks the result:
rocket_job_run(): rocket_fence_create(core), core->dev
rocket_job_timedout(): dev_err(core->dev, "NPU job timed out")
Unbinding the middle core of the three on an RK3588 while three clients are
submitting to all of them faults twice, once from the surviving core's
job queue and once from its reset work:
KASAN: null-ptr-deref in range [0x0000000000000220-0x0000000000000227]
Workqueue: fdad0000.npu drm_sched_run_job_work [gpu_sched]
pc : rocket_job_run+0x234/0x838 [rocket]
Call trace:
rocket_job_run+0x234/0x838 [rocket]
drm_sched_run_job_work+0x2cc/0xad8 [gpu_sched]
process_one_work+0x640/0x14f0
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
Workqueue: rocket-reset-2 drm_sched_job_timedout [gpu_sched]
pc : rocket_job_timedout+0xf0/0x1e0 [rocket]
Call trace:
rocket_job_timedout+0xf0/0x1e0 [rocket]
drm_sched_job_timedout+0x188/0x6a0 [gpu_sched]
Both are the third core: the workqueue names are its device and its
core->index, and it was left at slot 2 while num_cores had dropped to 2.
Search all the slots that were allocated, the way find_core_for_dev() now
does. A core that is still bound is then found, and the two callers get
the pointer they already assume they have.
This does not make unbinding one core out of several safe. An open client
keeps an entity pointing at the scheduler of the core that went away:
drm_sched reports it as not ready for every job that lands on it, and the
client waits in dma_fence_default_wait for a fence that will never signal.
Stopping the NULL dereference is what belongs in a fix; the rest wants
more thought. |
| In fixInitiatingUserIfNecessary of CallIntentProcessor.java, there is a possible way to make an emergency call due to a logic error in the code. This could lead to local escalation with User execution privileges needed. User interaction is needed for exploitation. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: nau8821: Cancel delayed work on component remove
Attempting to unload the driver while a jack detection work is pending
would likely crash the kernel when it is eventually scheduled for
execution:
[ 1984.896308] BUG: unable to handle page fault for address: ffffffffc10c2a20
[...]
[ 1984.896388] Hardware name: Valve Jupiter/Jupiter, BIOS F7A0131 01/30/2024
[ 1984.896396] Workqueue: events nau8821_jdet_work [snd_soc_nau8821]
[ 1984.896414] RIP: 0010:__mutex_lock+0x9f/0x11d0
[...]
[ 1984.896504] Call Trace:
[ 1984.896511] <TASK>
[ 1984.896524] ? snd_soc_dapm_disable_pin+0x26/0x60 [snd_soc_core]
[ 1984.896572] ? snd_soc_dapm_disable_pin+0x26/0x60 [snd_soc_core]
[ 1984.896596] snd_soc_dapm_disable_pin+0x26/0x60 [snd_soc_core]
[ 1984.896622] nau8821_jdet_work+0xeb/0x1e0 [snd_soc_nau8821]
[ 1984.896636] process_one_work+0x211/0x590
[ 1984.896649] ? srso_return_thunk+0x5/0x5f
[ 1984.896670] worker_thread+0x1cd/0x3a0
Cancel unscheduled jdet_work or wait for its execution to finish before
the component driver gets removed. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: intel-ish-hid: fix NULL-ptr-deref in ishtp_bus_remove_all_clients
During a warm reset flow, the cl->device pointer may be NULL if the
reset occurs while clients are still being enumerated. Accessing
cl->device->reference_count without a NULL check leads to a kernel panic.
This issue was identified during multi-unit warm reboot stress clycles.
Add a defensive NULL check for cl->device to ensure stability under
such intensive testing conditions.
KASAN: null-ptr-deref in range [0000000000000000-0000000000000007]
Workqueue: ish_fw_update_wq fw_reset_work_fn
Call Trace:
ishtp_bus_remove_all_clients+0xbe/0x130 [intel_ishtp]
ishtp_reset_handler+0x85/0x1a0 [intel_ishtp]
fw_reset_work_fn+0x8a/0xc0 [intel_ish_ipc] |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: csiostor: Fix dereference of null pointer rn
The error exit path when rn is NULL ends up deferencing the null pointer rn
via the use of the macro CSIO_INC_STATS. Fix this by adding a new error
return path label after the use of the macro to avoid the deference. |
| In the Linux kernel, the following vulnerability has been resolved:
bareudp: fix NULL pointer dereference in bareudp_fill_metadata_dst()
bareudp_fill_metadata_dst() passes bareudp->sock to
udp_tunnel6_dst_lookup() in the IPv6 path without a NULL check.
The socket is only created in bareudp_open() and NULLed in
bareudp_stop(), so calling this function while the device is down
triggers a NULL dereference via sock->sk.
BUG: kernel NULL pointer dereference, address: 0000000000000018
RIP: 0010:udp_tunnel6_dst_lookup (net/ipv6/ip6_udp_tunnel.c:160)
Call Trace:
<TASK>
bareudp_fill_metadata_dst (drivers/net/bareudp.c:532)
do_execute_actions (net/openvswitch/actions.c:901)
ovs_execute_actions (net/openvswitch/actions.c:1589)
ovs_packet_cmd_execute (net/openvswitch/datapath.c:700)
genl_family_rcv_msg_doit (net/netlink/genetlink.c:1114)
genl_rcv_msg (net/netlink/genetlink.c:1209)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
</TASK>
Add a NULL check returning -ESHUTDOWN, consistent with the xmit paths
in the same driver. |
