| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: fix out-of-bounds access during multi-link element defragmentation
Currently during the multi-link element defragmentation process, the
multi-link element length added to the total IEs length when calculating
the length of remaining IEs after the multi-link element in
cfg80211_defrag_mle(). This could lead to out-of-bounds access if the
multi-link element or its corresponding fragment elements are the last
elements in the IEs buffer.
To address this issue, correctly calculate the remaining IEs length by
deducting the multi-link element end offset from total IEs end offset. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Forcibly leave SMM mode on SHUTDOWN interception
Previously, commit ed129ec9057f ("KVM: x86: forcibly leave nested mode
on vCPU reset") addressed an issue where a triple fault occurring in
nested mode could lead to use-after-free scenarios. However, the commit
did not handle the analogous situation for System Management Mode (SMM).
This omission results in triggering a WARN when KVM forces a vCPU INIT
after SHUTDOWN interception while the vCPU is in SMM. This situation was
reprodused using Syzkaller by:
1) Creating a KVM VM and vCPU
2) Sending a KVM_SMI ioctl to explicitly enter SMM
3) Executing invalid instructions causing consecutive exceptions and
eventually a triple fault
The issue manifests as follows:
WARNING: CPU: 0 PID: 25506 at arch/x86/kvm/x86.c:12112
kvm_vcpu_reset+0x1d2/0x1530 arch/x86/kvm/x86.c:12112
Modules linked in:
CPU: 0 PID: 25506 Comm: syz-executor.0 Not tainted
6.1.130-syzkaller-00157-g164fe5dde9b6 #0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.12.0-1 04/01/2014
RIP: 0010:kvm_vcpu_reset+0x1d2/0x1530 arch/x86/kvm/x86.c:12112
Call Trace:
<TASK>
shutdown_interception+0x66/0xb0 arch/x86/kvm/svm/svm.c:2136
svm_invoke_exit_handler+0x110/0x530 arch/x86/kvm/svm/svm.c:3395
svm_handle_exit+0x424/0x920 arch/x86/kvm/svm/svm.c:3457
vcpu_enter_guest arch/x86/kvm/x86.c:10959 [inline]
vcpu_run+0x2c43/0x5a90 arch/x86/kvm/x86.c:11062
kvm_arch_vcpu_ioctl_run+0x50f/0x1cf0 arch/x86/kvm/x86.c:11283
kvm_vcpu_ioctl+0x570/0xf00 arch/x86/kvm/../../../virt/kvm/kvm_main.c:4122
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x19a/0x210 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x35/0x80 arch/x86/entry/common.c:81
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Architecturally, INIT is blocked when the CPU is in SMM, hence KVM's WARN()
in kvm_vcpu_reset() to guard against KVM bugs, e.g. to detect improper
emulation of INIT. SHUTDOWN on SVM is a weird edge case where KVM needs to
do _something_ sane with the VMCB, since it's technically undefined, and
INIT is the least awful choice given KVM's ABI.
So, double down on stuffing INIT on SHUTDOWN, and force the vCPU out of
SMM to avoid any weirdness (and the WARN).
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
[sean: massage changelog, make it clear this isn't architectural behavior] |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: prevent rename with empty string
Client can send empty newname string to ksmbd server.
It will cause a kernel oops from d_alloc.
This patch return the error when attempting to rename
a file or directory with an empty new name string. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: Avoid race in open_cached_dir with lease breaks
A pre-existing valid cfid returned from find_or_create_cached_dir might
race with a lease break, meaning open_cached_dir doesn't consider it
valid, and thinks it's newly-constructed. This leaks a dentry reference
if the allocation occurs before the queued lease break work runs.
Avoid the race by extending holding the cfid_list_lock across
find_or_create_cached_dir and when the result is checked. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: Fix UAF in __close_file_table_ids
A use-after-free is possible if one thread destroys the file
via __ksmbd_close_fd while another thread holds a reference to
it. The existing checks on fp->refcount are not sufficient to
prevent this.
The fix takes ft->lock around the section which removes the
file from the file table. This prevents two threads acquiring the
same file pointer via __close_file_table_ids, as well as the other
functions which retrieve a file from the IDR and which already use
this same lock. |
| In the Linux kernel, the following vulnerability has been resolved:
xenbus: Use kref to track req lifetime
Marek reported seeing a NULL pointer fault in the xenbus_thread
callstack:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: e030:__wake_up_common+0x4c/0x180
Call Trace:
<TASK>
__wake_up_common_lock+0x82/0xd0
process_msg+0x18e/0x2f0
xenbus_thread+0x165/0x1c0
process_msg+0x18e is req->cb(req). req->cb is set to xs_wake_up(), a
thin wrapper around wake_up(), or xenbus_dev_queue_reply(). It seems
like it was xs_wake_up() in this case.
It seems like req may have woken up the xs_wait_for_reply(), which
kfree()ed the req. When xenbus_thread resumes, it faults on the zero-ed
data.
Linux Device Drivers 2nd edition states:
"Normally, a wake_up call can cause an immediate reschedule to happen,
meaning that other processes might run before wake_up returns."
... which would match the behaviour observed.
Change to keeping two krefs on each request. One for the caller, and
one for xenbus_thread. Each will kref_put() when finished, and the last
will free it.
This use of kref matches the description in
Documentation/core-api/kref.rst |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: prevent out-of-bounds stream writes by validating *pos
ksmbd_vfs_stream_write() did not validate whether the write offset
(*pos) was within the bounds of the existing stream data length (v_len).
If *pos was greater than or equal to v_len, this could lead to an
out-of-bounds memory write.
This patch adds a check to ensure *pos is less than v_len before
proceeding. If the condition fails, -EINVAL is returned. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: Fix invalid entry fetch in ath12k_dp_mon_srng_process
Currently, ath12k_dp_mon_srng_process uses ath12k_hal_srng_src_get_next_entry
to fetch the next entry from the destination ring. This is incorrect because
ath12k_hal_srng_src_get_next_entry is intended for source rings, not destination
rings. This leads to invalid entry fetches, causing potential data corruption or
crashes due to accessing incorrect memory locations. This happens because the
source ring and destination ring have different handling mechanisms and using
the wrong function results in incorrect pointer arithmetic and ring management.
To fix this issue, replace the call to ath12k_hal_srng_src_get_next_entry with
ath12k_hal_srng_dst_get_next_entry in ath12k_dp_mon_srng_process. This ensures
that the correct function is used for fetching entries from the destination
ring, preventing invalid memory accesses.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: Fix invalid data access in ath12k_dp_rx_h_undecap_nwifi
In certain cases, hardware might provide packets with a
length greater than the maximum native Wi-Fi header length.
This can lead to accessing and modifying fields in the header
within the ath12k_dp_rx_h_undecap_nwifi function for
DP_RX_DECAP_TYPE_NATIVE_WIFI decap type and
potentially resulting in invalid data access and memory corruption.
Add a sanity check before processing the SKB to prevent invalid
data access in the undecap native Wi-Fi function for the
DP_RX_DECAP_TYPE_NATIVE_WIFI decap type.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk_eth_soc: fix SER panic with 4GB+ RAM
If the mtk_poll_rx() function detects the MTK_RESETTING flag, it will
jump to release_desc and refill the high word of the SDP on the 4GB RFB.
Subsequently, mtk_rx_clean will process an incorrect SDP, leading to a
panic.
Add patch from MediaTek's SDK to resolve this. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: adjust subpage bit start based on sectorsize
When running machines with 64k page size and a 16k nodesize we started
seeing tree log corruption in production. This turned out to be because
we were not writing out dirty blocks sometimes, so this in fact affects
all metadata writes.
When writing out a subpage EB we scan the subpage bitmap for a dirty
range. If the range isn't dirty we do
bit_start++;
to move onto the next bit. The problem is the bitmap is based on the
number of sectors that an EB has. So in this case, we have a 64k
pagesize, 16k nodesize, but a 4k sectorsize. This means our bitmap is 4
bits for every node. With a 64k page size we end up with 4 nodes per
page.
To make this easier this is how everything looks
[0 16k 32k 48k ] logical address
[0 4 8 12 ] radix tree offset
[ 64k page ] folio
[ 16k eb ][ 16k eb ][ 16k eb ][ 16k eb ] extent buffers
[ | | | | | | | | | | | | | | | | ] bitmap
Now we use all of our addressing based on fs_info->sectorsize_bits, so
as you can see the above our 16k eb->start turns into radix entry 4.
When we find a dirty range for our eb, we correctly do bit_start +=
sectors_per_node, because if we start at bit 0, the next bit for the
next eb is 4, to correspond to eb->start 16k.
However if our range is clean, we will do bit_start++, which will now
put us offset from our radix tree entries.
In our case, assume that the first time we check the bitmap the block is
not dirty, we increment bit_start so now it == 1, and then we loop
around and check again. This time it is dirty, and we go to find that
start using the following equation
start = folio_start + bit_start * fs_info->sectorsize;
so in the case above, eb->start 0 is now dirty, and we calculate start
as
0 + 1 * fs_info->sectorsize = 4096
4096 >> 12 = 1
Now we're looking up the radix tree for 1, and we won't find an eb.
What's worse is now we're using bit_start == 1, so we do bit_start +=
sectors_per_node, which is now 5. If that eb is dirty we will run into
the same thing, we will look at an offset that is not populated in the
radix tree, and now we're skipping the writeout of dirty extent buffers.
The best fix for this is to not use sectorsize_bits to address nodes,
but that's a larger change. Since this is a fs corruption problem fix
it simply by always using sectors_per_node to increment the start bit. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in ksmbd_session_rpc_open
A UAF issue can occur due to a race condition between
ksmbd_session_rpc_open() and __session_rpc_close().
Add rpc_lock to the session to protect it. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Fix out-of-bound memcpy() during ethtool -w
When retrieving the FW coredump using ethtool, it can sometimes cause
memory corruption:
BUG: KFENCE: memory corruption in __bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
Corrupted memory at 0x000000008f0f30e8 [ ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ] (in kfence-#45):
__bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
ethtool_get_dump_data+0xdc/0x1a0
__dev_ethtool+0xa1e/0x1af0
dev_ethtool+0xa8/0x170
dev_ioctl+0x1b5/0x580
sock_do_ioctl+0xab/0xf0
sock_ioctl+0x1ce/0x2e0
__x64_sys_ioctl+0x87/0xc0
do_syscall_64+0x5c/0xf0
entry_SYSCALL_64_after_hwframe+0x78/0x80
...
This happens when copying the coredump segment list in
bnxt_hwrm_dbg_dma_data() with the HWRM_DBG_COREDUMP_LIST FW command.
The info->dest_buf buffer is allocated based on the number of coredump
segments returned by the FW. The segment list is then DMA'ed by
the FW and the length of the DMA is returned by FW. The driver then
copies this DMA'ed segment list to info->dest_buf.
In some cases, this DMA length may exceed the info->dest_buf length
and cause the above BUG condition. Fix it by capping the copy
length to not exceed the length of info->dest_buf. The extra
DMA data contains no useful information.
This code path is shared for the HWRM_DBG_COREDUMP_LIST and the
HWRM_DBG_COREDUMP_RETRIEVE FW commands. The buffering is different
for these 2 FW commands. To simplify the logic, we need to move
the line to adjust the buffer length for HWRM_DBG_COREDUMP_RETRIEVE
up, so that the new check to cap the copy length will work for both
commands. |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: fix race between io_uring_cmd_complete_in_task and ublk_cancel_cmd
ublk_cancel_cmd() calls io_uring_cmd_done() to complete uring_cmd, but
we may have scheduled task work via io_uring_cmd_complete_in_task() for
dispatching request, then kernel crash can be triggered.
Fix it by not trying to canceling the command if ublk block request is
started. |
| In the Linux kernel, the following vulnerability has been resolved:
irqchip/qcom-mpm: Prevent crash when trying to handle non-wake GPIOs
On Qualcomm chipsets not all GPIOs are wakeup capable. Those GPIOs do not
have a corresponding MPM pin and should not be handled inside the MPM
driver. The IRQ domain hierarchy is always applied, so it's required to
explicitly disconnect the hierarchy for those. The pinctrl-msm driver marks
these with GPIO_NO_WAKE_IRQ. qcom-pdc has a check for this, but
irq-qcom-mpm is currently missing the check. This is causing crashes when
setting up interrupts for non-wake GPIOs:
root@rb1:~# gpiomon -c gpiochip1 10
irq: IRQ159: trimming hierarchy from :soc@0:interrupt-controller@f200000-1
Unable to handle kernel paging request at virtual address ffff8000a1dc3820
Hardware name: Qualcomm Technologies, Inc. Robotics RB1 (DT)
pc : mpm_set_type+0x80/0xcc
lr : mpm_set_type+0x5c/0xcc
Call trace:
mpm_set_type+0x80/0xcc (P)
qcom_mpm_set_type+0x64/0x158
irq_chip_set_type_parent+0x20/0x38
msm_gpio_irq_set_type+0x50/0x530
__irq_set_trigger+0x60/0x184
__setup_irq+0x304/0x6bc
request_threaded_irq+0xc8/0x19c
edge_detector_setup+0x260/0x364
linereq_create+0x420/0x5a8
gpio_ioctl+0x2d4/0x6c0
Fix this by copying the check for GPIO_NO_WAKE_IRQ from qcom-pdc.c, so that
MPM is removed entirely from the hierarchy for non-wake GPIOs. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in session logoff
The sess->user object can currently be in use by another thread, for
example if another connection has sent a session setup request to
bind to the session being free'd. The handler for that connection could
be in the smb2_sess_setup function which makes use of sess->user. |
| In the Linux kernel, the following vulnerability has been resolved:
net: use sock_gen_put() when sk_state is TCP_TIME_WAIT
It is possible for a pointer of type struct inet_timewait_sock to be
returned from the functions __inet_lookup_established() and
__inet6_lookup_established(). This can cause a crash when the
returned pointer is of type struct inet_timewait_sock and
sock_put() is called on it. The following is a crash call stack that
shows sk->sk_wmem_alloc being accessed in sk_free() during the call to
sock_put() on a struct inet_timewait_sock pointer. To avoid this issue,
use sock_gen_put() instead of sock_put() when sk->sk_state
is TCP_TIME_WAIT.
mrdump.ko ipanic() + 120
vmlinux notifier_call_chain(nr_to_call=-1, nr_calls=0) + 132
vmlinux atomic_notifier_call_chain(val=0) + 56
vmlinux panic() + 344
vmlinux add_taint() + 164
vmlinux end_report() + 136
vmlinux kasan_report(size=0) + 236
vmlinux report_tag_fault() + 16
vmlinux do_tag_recovery() + 16
vmlinux __do_kernel_fault() + 88
vmlinux do_bad_area() + 28
vmlinux do_tag_check_fault() + 60
vmlinux do_mem_abort() + 80
vmlinux el1_abort() + 56
vmlinux el1h_64_sync_handler() + 124
vmlinux > 0xFFFFFFC080011294()
vmlinux __lse_atomic_fetch_add_release(v=0xF2FFFF82A896087C)
vmlinux __lse_atomic_fetch_sub_release(v=0xF2FFFF82A896087C)
vmlinux arch_atomic_fetch_sub_release(i=1, v=0xF2FFFF82A896087C)
+ 8
vmlinux raw_atomic_fetch_sub_release(i=1, v=0xF2FFFF82A896087C)
+ 8
vmlinux atomic_fetch_sub_release(i=1, v=0xF2FFFF82A896087C) + 8
vmlinux __refcount_sub_and_test(i=1, r=0xF2FFFF82A896087C,
oldp=0) + 8
vmlinux __refcount_dec_and_test(r=0xF2FFFF82A896087C, oldp=0) + 8
vmlinux refcount_dec_and_test(r=0xF2FFFF82A896087C) + 8
vmlinux sk_free(sk=0xF2FFFF82A8960700) + 28
vmlinux sock_put() + 48
vmlinux tcp6_check_fraglist_gro() + 236
vmlinux tcp6_gro_receive() + 624
vmlinux ipv6_gro_receive() + 912
vmlinux dev_gro_receive() + 1116
vmlinux napi_gro_receive() + 196
ccmni.ko ccmni_rx_callback() + 208
ccmni.ko ccmni_queue_recv_skb() + 388
ccci_dpmaif.ko dpmaif_rxq_push_thread() + 1088
vmlinux kthread() + 268
vmlinux 0xFFFFFFC08001F30C() |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: BPF: Fix off-by-one error in build_prologue()
Vincent reported that running BPF progs with tailcalls on LoongArch
causes kernel hard lockup. Debugging the issues shows that the JITed
image missing a jirl instruction at the end of the epilogue.
There are two passes in JIT compiling, the first pass set the flags and
the second pass generates JIT code based on those flags. With BPF progs
mixing bpf2bpf and tailcalls, build_prologue() generates N insns in the
first pass and then generates N+1 insns in the second pass. This makes
epilogue_offset off by one and we will jump to some unexpected insn and
cause lockup. Fix this by inserting a nop insn. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: handle unsupported PDS_CORE_CMD_FW_CONTROL result
If the FW doesn't support the PDS_CORE_CMD_FW_CONTROL command
the driver might at the least print garbage and at the worst
crash when the user runs the "devlink dev info" devlink command.
This happens because the stack variable fw_list is not 0
initialized which results in fw_list.num_fw_slots being a
garbage value from the stack. Then the driver tries to access
fw_list.fw_names[i] with i >= ARRAY_SIZE and runs off the end
of the array.
Fix this by initializing the fw_list and by not failing
completely if the devcmd fails because other useful information
is printed via devlink dev info even if the devcmd fails. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: make wait_context part of q_info
Make the wait_context a full part of the q_info struct rather
than a stack variable that goes away after pdsc_adminq_post()
is done so that the context is still available after the wait
loop has given up.
There was a case where a slow development firmware caused
the adminq request to time out, but then later the FW finally
finished the request and sent the interrupt. The handler tried
to complete_all() the completion context that had been created
on the stack in pdsc_adminq_post() but no longer existed.
This caused bad pointer usage, kernel crashes, and much wailing
and gnashing of teeth. |
