| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| An uninitialized pointer dereference in the NasPdu::NasPdu component of OpenAirInterface CN5G AMF up to v2.0.0 allows attackers to cause a Denial of Service (DoS) via a crafted InitialUEMessage message sent to the AMF. |
| In the Linux kernel, the following vulnerability has been resolved:
ping: Fix potentail NULL deref for /proc/net/icmp.
After commit dbca1596bbb0 ("ping: convert to RCU lookups, get rid
of rwlock"), we use RCU for ping sockets, but we should use spinlock
for /proc/net/icmp to avoid a potential NULL deref mentioned in
the previous patch.
Let's go back to using spinlock there.
Note we can convert ping sockets to use hlist instead of hlist_nulls
because we do not use SLAB_TYPESAFE_BY_RCU for ping sockets. |
| Stack-based memcpy buffer overflow in the ngap_handle_pdu_session_resource_setup_response routine in OpenAirInterface CN5G AMF <= 2.0.0 allows a remote attacker with access to the N2 interface to carry out denial of service against the AMF and potentially execute code by sending a PDU Session Resource Setup Response with a suffciently large FailedToSetupList IE. |
| An invalid memory access when handling the ProtocolIE_ID field of E-RAB Release Indication messages in Athonet vEPC MME v11.4.0 allows attackers to cause a Denial of Service (DoS) to the cellular network by repeatedly initiating connections and sending a crafted payload. |
| An invalid memory access when handling the ProtocolIE_ID field of E-RAB NotToBeModifiedBearerModInd information element in Athonet vEPC MME v11.4.0 allows attackers to cause a Denial of Service (DoS) to the cellular network by repeatedly initiating connections and sending a crafted payload. |
| An invalid memory access when handling the ProtocolIE_ID field of E-RAB Modify Request messages in Athonet vEPC MME v11.4.0 allows attackers to cause a Denial of Service (DoS) to the cellular network by repeatedly initiating connections and sending a crafted payload. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: handle case when repair happens with dev-replace
[BUG]
There is a bug report that a BUG_ON() in btrfs_repair_io_failure()
(originally repair_io_failure() in v6.0 kernel) got triggered when
replacing a unreliable disk:
BTRFS warning (device sda1): csum failed root 257 ino 2397453 off 39624704 csum 0xb0d18c75 expected csum 0x4dae9c5e mirror 3
kernel BUG at fs/btrfs/extent_io.c:2380!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 9 PID: 3614331 Comm: kworker/u257:2 Tainted: G OE 6.0.0-5-amd64 #1 Debian 6.0.10-2
Hardware name: Micro-Star International Co., Ltd. MS-7C60/TRX40 PRO WIFI (MS-7C60), BIOS 2.70 07/01/2021
Workqueue: btrfs-endio btrfs_end_bio_work [btrfs]
RIP: 0010:repair_io_failure+0x24a/0x260 [btrfs]
Call Trace:
<TASK>
clean_io_failure+0x14d/0x180 [btrfs]
end_bio_extent_readpage+0x412/0x6e0 [btrfs]
? __switch_to+0x106/0x420
process_one_work+0x1c7/0x380
worker_thread+0x4d/0x380
? rescuer_thread+0x3a0/0x3a0
kthread+0xe9/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
[CAUSE]
Before the BUG_ON(), we got some read errors from the replace target
first, note the mirror number (3, which is beyond RAID1 duplication,
thus it's read from the replace target device).
Then at the BUG_ON() location, we are trying to writeback the repaired
sectors back the failed device.
The check looks like this:
ret = btrfs_map_block(fs_info, BTRFS_MAP_WRITE, logical,
&map_length, &bioc, mirror_num);
if (ret)
goto out_counter_dec;
BUG_ON(mirror_num != bioc->mirror_num);
But inside btrfs_map_block(), we can modify bioc->mirror_num especially
for dev-replace:
if (dev_replace_is_ongoing && mirror_num == map->num_stripes + 1 &&
!need_full_stripe(op) && dev_replace->tgtdev != NULL) {
ret = get_extra_mirror_from_replace(fs_info, logical, *length,
dev_replace->srcdev->devid,
&mirror_num,
&physical_to_patch_in_first_stripe);
patch_the_first_stripe_for_dev_replace = 1;
}
Thus if we're repairing the replace target device, we're going to
trigger that BUG_ON().
But in reality, the read failure from the replace target device may be
that, our replace hasn't reached the range we're reading, thus we're
reading garbage, but with replace running, the range would be properly
filled later.
Thus in that case, we don't need to do anything but let the replace
routine to handle it.
[FIX]
Instead of a BUG_ON(), just skip the repair if we're repairing the
device replace target device. |
| A flaw was found in the RPC library APIs of libvirt. The RPC server deserialization code allocates memory for arrays before the non-negative length check is performed by the C API entry points. Passing a negative length to the g_new0 function results in a crash due to the negative length being treated as a huge positive number. This flaw allows a local, unprivileged user to perform a denial of service attack by causing the libvirt daemon to crash. |
| In the Linux kernel, the following vulnerability has been resolved:
pstore/ram: Add check for kstrdup
Add check for the return value of kstrdup() and return the error
if it fails in order to avoid NULL pointer dereference. |
| In illumos illumos-gate 2024-02-15, an error occurs in the elliptic curve point addition algorithm that uses mixed Jacobian-affine coordinates, causing the algorithm to yield a result of POINT_AT_INFINITY when it should not. A man-in-the-middle attacker could use this to interfere with a connection, resulting in an attacked party computing an incorrect shared secret. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Fix memory leak of PBLE objects
On rmmod of irdma, the PBLE object memory is not being freed. PBLE object
memory are not statically pre-allocated at function initialization time
unlike other HMC objects. PBLEs objects and the Segment Descriptors (SD)
for it can be dynamically allocated during scale up and SD's remain
allocated till function deinitialization.
Fix this leak by adding IRDMA_HMC_IW_PBLE to the iw_hmc_obj_types[] table
and skip pbles in irdma_create_hmc_obj but not in irdma_del_hmc_objects(). |
| In the Linux kernel, the following vulnerability has been resolved:
kheaders: Use array declaration instead of char
Under CONFIG_FORTIFY_SOURCE, memcpy() will check the size of destination
and source buffers. Defining kernel_headers_data as "char" would trip
this check. Since these addresses are treated as byte arrays, define
them as arrays (as done everywhere else).
This was seen with:
$ cat /sys/kernel/kheaders.tar.xz >> /dev/null
detected buffer overflow in memcpy
kernel BUG at lib/string_helpers.c:1027!
...
RIP: 0010:fortify_panic+0xf/0x20
[...]
Call Trace:
<TASK>
ikheaders_read+0x45/0x50 [kheaders]
kernfs_fop_read_iter+0x1a4/0x2f0
... |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Add a length limitation for the ivrs_acpihid command-line parameter
The 'acpiid' buffer in the parse_ivrs_acpihid function may overflow,
because the string specifier in the format string sscanf()
has no width limitation.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
ipmi:ssif: Fix a memory leak when scanning for an adapter
The adapter scan ssif_info_find() sets info->adapter_name if the adapter
info came from SMBIOS, as it's not set in that case. However, this
function can be called more than once, and it will leak the adapter name
if it had already been set. So check for NULL before setting it. |
| In the Linux kernel, the following vulnerability has been resolved:
igb: clean up in all error paths when enabling SR-IOV
After commit 50f303496d92 ("igb: Enable SR-IOV after reinit"), removing
the igb module could hang or crash (depending on the machine) when the
module has been loaded with the max_vfs parameter set to some value != 0.
In case of one test machine with a dual port 82580, this hang occurred:
[ 232.480687] igb 0000:41:00.1: removed PHC on enp65s0f1
[ 233.093257] igb 0000:41:00.1: IOV Disabled
[ 233.329969] pcieport 0000:40:01.0: AER: Multiple Uncorrected (Non-Fatal) err0
[ 233.340302] igb 0000:41:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.352248] igb 0000:41:00.0: device [8086:1516] error status/mask=00100000
[ 233.361088] igb 0000:41:00.0: [20] UnsupReq (First)
[ 233.368183] igb 0000:41:00.0: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.376846] igb 0000:41:00.1: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.388779] igb 0000:41:00.1: device [8086:1516] error status/mask=00100000
[ 233.397629] igb 0000:41:00.1: [20] UnsupReq (First)
[ 233.404736] igb 0000:41:00.1: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.538214] pci 0000:41:00.1: AER: can't recover (no error_detected callback)
[ 233.538401] igb 0000:41:00.0: removed PHC on enp65s0f0
[ 233.546197] pcieport 0000:40:01.0: AER: device recovery failed
[ 234.157244] igb 0000:41:00.0: IOV Disabled
[ 371.619705] INFO: task irq/35-aerdrv:257 blocked for more than 122 seconds.
[ 371.627489] Not tainted 6.4.0-dirty #2
[ 371.632257] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this.
[ 371.641000] task:irq/35-aerdrv state:D stack:0 pid:257 ppid:2 f0
[ 371.650330] Call Trace:
[ 371.653061] <TASK>
[ 371.655407] __schedule+0x20e/0x660
[ 371.659313] schedule+0x5a/0xd0
[ 371.662824] schedule_preempt_disabled+0x11/0x20
[ 371.667983] __mutex_lock.constprop.0+0x372/0x6c0
[ 371.673237] ? __pfx_aer_root_reset+0x10/0x10
[ 371.678105] report_error_detected+0x25/0x1c0
[ 371.682974] ? __pfx_report_normal_detected+0x10/0x10
[ 371.688618] pci_walk_bus+0x72/0x90
[ 371.692519] pcie_do_recovery+0xb2/0x330
[ 371.696899] aer_process_err_devices+0x117/0x170
[ 371.702055] aer_isr+0x1c0/0x1e0
[ 371.705661] ? __set_cpus_allowed_ptr+0x54/0xa0
[ 371.710723] ? __pfx_irq_thread_fn+0x10/0x10
[ 371.715496] irq_thread_fn+0x20/0x60
[ 371.719491] irq_thread+0xe6/0x1b0
[ 371.723291] ? __pfx_irq_thread_dtor+0x10/0x10
[ 371.728255] ? __pfx_irq_thread+0x10/0x10
[ 371.732731] kthread+0xe2/0x110
[ 371.736243] ? __pfx_kthread+0x10/0x10
[ 371.740430] ret_from_fork+0x2c/0x50
[ 371.744428] </TASK>
The reproducer was a simple script:
#!/bin/sh
for i in `seq 1 5`; do
modprobe -rv igb
modprobe -v igb max_vfs=1
sleep 1
modprobe -rv igb
done
It turned out that this could only be reproduce on 82580 (quad and
dual-port), but not on 82576, i350 and i210. Further debugging showed
that igb_enable_sriov()'s call to pci_enable_sriov() is failing, because
dev->is_physfn is 0 on 82580.
Prior to commit 50f303496d92 ("igb: Enable SR-IOV after reinit"),
igb_enable_sriov() jumped into the "err_out" cleanup branch. After this
commit it only returned the error code.
So the cleanup didn't take place, and the incorrect VF setup in the
igb_adapter structure fooled the igb driver into assuming that VFs have
been set up where no VF actually existed.
Fix this problem by cleaning up again if pci_enable_sriov() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
media: max9286: Free control handler
The control handler is leaked in some probe-time error paths, as well as
in the remove path. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Fix potential data race at PCM memory allocation helpers
The PCM memory allocation helpers have a sanity check against too many
buffer allocations. However, the check is performed without a proper
lock and the allocation isn't serialized; this allows user to allocate
more memories than predefined max size.
Practically seen, this isn't really a big problem, as it's more or
less some "soft limit" as a sanity check, and it's not possible to
allocate unlimitedly. But it's still better to address this for more
consistent behavior.
The patch covers the size check in do_alloc_pages() with the
card->memory_mutex, and increases the allocated size there for
preventing the further overflow. When the actual allocation fails,
the size is decreased accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: check CAN address family in isotp_bind()
Add missing check to block non-AF_CAN binds.
Syzbot created some code which matched the right sockaddr struct size
but used AF_XDP (0x2C) instead of AF_CAN (0x1D) in the address family
field:
bind$xdp(r2, &(0x7f0000000540)={0x2c, 0x0, r4, 0x0, r2}, 0x10)
^^^^
This has no funtional impact but the userspace should be notified about
the wrong address family field content. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Add preempt_count_{sub,add} into btf id deny list
The recursion check in __bpf_prog_enter* and __bpf_prog_exit*
leave preempt_count_{sub,add} unprotected. When attaching trampoline to
them we get panic as follows,
[ 867.843050] BUG: TASK stack guard page was hit at 0000000009d325cf (stack is 0000000046a46a15..00000000537e7b28)
[ 867.843064] stack guard page: 0000 [#1] PREEMPT SMP NOPTI
[ 867.843067] CPU: 8 PID: 11009 Comm: trace Kdump: loaded Not tainted 6.2.0+ #4
[ 867.843100] Call Trace:
[ 867.843101] <TASK>
[ 867.843104] asm_exc_int3+0x3a/0x40
[ 867.843108] RIP: 0010:preempt_count_sub+0x1/0xa0
[ 867.843135] __bpf_prog_enter_recur+0x17/0x90
[ 867.843148] bpf_trampoline_6442468108_0+0x2e/0x1000
[ 867.843154] ? preempt_count_sub+0x1/0xa0
[ 867.843157] preempt_count_sub+0x5/0xa0
[ 867.843159] ? migrate_enable+0xac/0xf0
[ 867.843164] __bpf_prog_exit_recur+0x2d/0x40
[ 867.843168] bpf_trampoline_6442468108_0+0x55/0x1000
...
[ 867.843788] preempt_count_sub+0x5/0xa0
[ 867.843793] ? migrate_enable+0xac/0xf0
[ 867.843829] __bpf_prog_exit_recur+0x2d/0x40
[ 867.843837] BUG: IRQ stack guard page was hit at 0000000099bd8228 (stack is 00000000b23e2bc4..000000006d95af35)
[ 867.843841] BUG: IRQ stack guard page was hit at 000000005ae07924 (stack is 00000000ffd69623..0000000014eb594c)
[ 867.843843] BUG: IRQ stack guard page was hit at 00000000028320f0 (stack is 00000000034b6438..0000000078d1bcec)
[ 867.843842] bpf_trampoline_6442468108_0+0x55/0x1000
...
That is because in __bpf_prog_exit_recur, the preempt_count_{sub,add} are
called after prog->active is decreased.
Fixing this by adding these two functions into btf ids deny list. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: stm32-pwr: fix of_iomap leak
Smatch reports:
drivers/regulator/stm32-pwr.c:166 stm32_pwr_regulator_probe() warn:
'base' from of_iomap() not released on lines: 151,166.
In stm32_pwr_regulator_probe(), base is not released
when devm_kzalloc() fails to allocate memory or
devm_regulator_register() fails to register a new regulator device,
which may cause a leak.
To fix this issue, replace of_iomap() with
devm_platform_ioremap_resource(). devm_platform_ioremap_resource()
is a specialized function for platform devices.
It allows 'base' to be automatically released whether the probe
function succeeds or fails.
Besides, use IS_ERR(base) instead of !base
as the return value of devm_platform_ioremap_resource()
can either be a pointer to the remapped memory or
an ERR_PTR() encoded error code if the operation fails. |
